-
Support plates
€ 29,31The Support plates ensure that the wooden plate is not dented by the wheels of the Carrier when it is loaded onto the veicle interface. For installation we advise you to watch the assembly film of the vehicle interface before starting assembly.Application:
Vehicle interface of all models -
Standard wheels
-
Set wheels support frames
€ 55,78The wheels support frames ensure that the carrier rolls on the car interface. It is very important that the bolts are properly greased during installation. This is to prevent frictional noise.Applications:
All models -
Set shaft with spring cotter
€ 14,09The “Shaft with spring cotter” forms the pivot points of the Loadingtray. These must be greased during assembly. For installation we advise you to watch the assembly film of the vehicle interface before starting assembly.Application:
Vehicle interface of all models -
Set safety locks
€ 147,60The safety locks are the part of the mechanism that lock and unlock the legs. Assembly requires some Dynnox expertise. The bolts should be mounted with loctite to prevent loosening of the screws. Note: when replacing these parts the clearance of the legs must be reset. See manual. Also watch our assembly video.Applications
All models -
These casters are usually used for flat surfaces for both indoors and outdoors. They can handle 70 kg per wheel. The use of these casters makes starting a carrier smoother.
-
Set of brackets
€ 175,25The Brackets are made of stainless steel and ensure the positioning and anchoring of the frame on the laoding tray. For installation we advise you to watch the assembly film of the vehicle interface before starting assembly.Application
Vehicle interface of all models -
Set locking lever
€ 19,26The locking lever locks the loading tray. This can be mounted with pop rivet and/or M4 bolts. These are not included.Applications:
Vehicle interface of all models -
Set levers loading platform
€ 53,76The levers loading platform secures the suspension of the loading tray when it is folded out. These can be easily disassembled so that the loading tray can be disconnected from the vehilcle interface. For installation we advise you to watch the assembly film of the vehicle interface before starting assembly.Application:
Vehicle interface of all models -
Set fixation locking knobs
€ 95,60The fixation locking knobs ensures that the frame is anchored in the brackets. Assembly requires some Dynnox expertise. You can find the instructions in the assembly film of the carrier.Applications
All models -
Set fasteners
€ 47,00The set of fasteners contain all small parts for mounting all parts of the car interface on the Dynnox wooden plate.Application:
All models -
Set Castor air wheel 200×40
€ 228,00Luchtband van 200 mm met zwenkwiel voor de Dynnox L46, XL36 en XL53. -
Set air wheels 260×85
€ 178,00Luchtband wiel van 260 mm voor de Dynnox L46, XL36 en XL53. -
Safety activator 53
€ 253,80The safety activator is part of the chassis. The safety activator is the most important part of Dynnox. When loading an undercarriage in a vehicle, the unlocking of the legs is hereby ensured. But also the locking of the legs when unloading a chassis. This part is for the Dynnox XL53. Note: the performance of the legs must be reset when these parts are replaced. See manual.Applications
Dynnox XL53 -
These casters are usually used for flat surfaces for both indoors and outdoors. They can handle 70 kg per wheel. The use of these casters makes starting a carrier smoother.
-
Loading tray 60
€ 380,16The loading tray is the platform on which the frame comes first. The sloping side of the platform ensures that the frame is lifted from the ground. The loading wheel should be halfway along the slope of the loading tray. At the front of the loading tray is also a small “platform” with a hook on it. This activates the mechanism and unlocks the legs. It is therefore important that the chassis is never higher than the loading tray.Application
Vehicle interface XL53 in combination with pneumatic tire option -
Loading tray 53
€ 342,90The loading tray is the platform on which the frame comes first. The sloping side of the platform ensures that the frame is lifted from the ground. The loading wheel should be halfway along the slope of the loading tray. At the front of the loading tray is also a small “platform” with a hook on it. This activates the mechanism and unlocks the legs. It is therefore important that the chassis is never higher than the loading tray.Application
Vehicle interface XL53 Vehicle interface XL46 in combination with pneumatic tire option -
Loading tray 53
€ 342,90The loading tray is the platform on which the frame comes first. The sloping side of the platform ensures that the frame is lifted from the ground. The loading wheel should be halfway along the slope of the loading tray. At the front of the loading tray is also a small “platform” with a hook on it. This activates the mechanism and unlocks the legs. It is therefore important that the chassis is never higher than the loading tray.Application
Vehicle interface XL53 Vehicle interface XL46 in combination with pneumatic tire option -
Guide rail left
€ 87,00The guide rail left provides guidance for the carrier when it is being loaded. For installation we advise you to watch the assembly film of the vehicle interface before starting assembly.Application:
Vehicle interface of all models -
Dynnox XL53 carrier
€ 1.250,00The chassis XL53 is the longest and widest Dynnox. The front and back are the same width. The car interface is not included. Due to its length and width, it is often used for bulky and / or complicated applications. An application of approx. 80 cm width, 140 length and 120 hight can be mounted on the frame, providing that the mass (load) is well distributed in the application. Read more about the XL53 or contact us! -
Detachable auto interface
€ 485,00The car interface can be removed in 5 minutes so that the floor of the vehicle can be used for other applications. For this you need rails and 6 knobs. The rails are mounted in the floor of the vehicle. They are 1.5 m long. For the Dynnox L46, these can be shortened to 1.2 m. The mounting of this rail is very important for safety. This must be mounted by an expert in the field of commercial vehicle installation. Due to the enormous variety of commercial vehicles, we cannot provide a universal installation manual for this. If your commercial vehicle installer wants to deliver this rail, he must apply the European dimensions. The 6 knobs have been tested at 2000 newtons. An important precondition for your safety. This is very specific mounting material that is not easy to obtain.Application:
All models -
Castor wheel rubber 200×40 mm
€ 76,50Standard wheels for all Dynnox models. -
Castor wheel rubber 150×40 mm
€ 67,85These wheels are similar in profile to the standard wheels, only slightly larger. -
Castor air wheel 200×40
€ 98,00Luchtband van 200 mm met zwenkwiel voor de Dynnox L46, XL36 en XL53. -
Caster wheel rubber 125×40 mm
€ 53,50Standard wheels -
Cable
€ 20,47This cable is used to unlock the car interface. The installation of this cable is very important for the correct functioning of the lock when an underframe is unloaded. We recommend that you watch the instruction film assembly auto interface.Application:
All models -
Air wheel 260×85 mm
€ 93,00Luchtband wiel van 260 mm voor de Dynnox L46, XL36 en XL53. -
The vehicle interface can be removed in 5 minutes so that the floor of the vehicle can be used for other applications. For this you need rails and 6 knobs. The rails are mounted in the floor of the vehicle. They are 1.5 m long. For the Dynnox L46, these can be shortened to 1.2 m. The mounting of this rail is very important for safety. This must be mounted by an expert in the field of commercial vehicle installation. Due to the enormous variety of commercial vehicles, we cannot provide a universal installation manual for this. If your commercial vehicle installer wants to deliver this rail, he must apply the European dimensions.
Application:
All models Prefer the complete set? Please check our Detachable vehicle interface. -
The car interface can be removed in 5 minutes so that the floor of the vehicle can be used for other applications. For this you need 6 knobs tested at 2000 newton. An important precondition for your safety. This is very specific mounting material that is not easy to obtain. This set contains 2 knobs for spare parts.
Application
All models Prefer the complete set? Please check our Detachable vehicle interface. -
The car interface can be removed in 5 minutes so that the floor of the vehicle can be used for other applications. For this you need 6 knobs tested at 2000 newton. An important precondition for your safety. This is very specific mounting material that is not easy to obtain.
Application:
All models Prefer the complete set? Please check our Detachable vehicle interface!
